About the pros and cons of PCB copper coating
Copper coating is an important part of PCB design. Whether it is the domestic Qingyuefeng PCB design software or some foreign Protel and PowerPCB, they all provide intelligent copper coating function. So how to coat copper well? I will share some of my ideas with you, hoping to benefit my peers.
The so-called copper coating is to use the idle space on the PCB as the reference surface and then fill it with solid copper.
These copper areas are also called copper filling. The significance of copper coating is to reduce the impedance of the ground line and improve the anti-interference ability; reduce the voltage drop and improve the power supply efficiency; connected to the ground line, it can also reduce the loop area. In order to make the PCB as deformable as possible during welding, most PCB manufacturers will also require PCB designers to fill the open area of PCB with copper or grid-shaped ground lines. If the copper coating is not handled properly, it will be more gain than loss. Is copper coating “more advantages than disadvantages” or “more disadvantages than advantages”?
As we all know, under high frequency conditions, the distributed capacitance of the wiring on the printed circuit board will play a role.
When the length is greater than 1/20 of the corresponding wavelength of the noise frequency, an antenna effect will be generated, and the noise will be emitted outward through the wiring. If there is a poorly grounded copper in the PCB, the copper becomes a tool for propagating noise. Therefore, in high-frequency circuits, do not think that connecting a certain part of the ground wire to the ground is the “ground wire”. It is necessary to drill holes in the wiring with a spacing less than λ/20 to “well ground” with the ground plane of the multilayer board. If the copper is properly processed, the copper not only increases the current, but also plays a dual role in shielding interference.
There are generally two basic ways to cover copper, namely large-area copper and grid copper.
People often ask whether large-area copper or grid copper is better, which is not easy to generalize. Why? Large-area copper has the dual functions of increasing current and shielding, but large-area copper may cause the board to warp or even bubble during wave soldering.
Therefore, for large-area copper cladding, several grooves are usually opened to alleviate the blistering of copper foil.
The main function of pure grid copper cladding is shielding, and the effect of increasing current is reduced. From the perspective of heat dissipation, the grid has advantages (it reduces the heating surface of copper) and plays a certain role in electromagnetic shielding. However, it should be pointed out that the grid is composed of traces in staggered directions.
We know that for the circuit, the width of the trace has a corresponding “electrical length” for the operating frequency of the circuit board (the actual size is divided by the digital frequency corresponding to the operating frequency, which can be obtained by referring to relevant books). When the operating frequency is not very high, the effect of the grid line may not be very obvious.
Once the electrical length matches the operating frequency, it will be very bad. You will find that the circuit cannot work properly at all, and signals that interfere with the operation of the system are emitted everywhere. So for colleagues who use grids, my suggestion is to choose according to the working conditions of the designed circuit board, and don’t stick to one thing. Therefore, high-frequency circuits with high requirements for anti-interference use grids, and low-frequency circuits with large currents often use complete copper cladding.
Having said so much, what should we pay attention to in order to achieve the expected effect of copper plating:
- If there are many grounds on the PCB, such as SGND, AGND, GND, etc., we should use the most important “ground” as the reference to independently plating copper according to the different positions of the PCB board. It goes without saying that the digital ground and analog ground are separately plating copper. At the same time, before plating copper, first thicken the corresponding power connection: 5.0V, 3.3V, etc., so that multiple deformable structures of different shapes are formed.
- For single-point connection of different grounds, the method is to connect through 0 ohm resistors, magnetic beads or inductors;
- Copper plating near the crystal oscillator. The crystal oscillator in the circuit is a high-frequency emission source. The method is to plating copper around the crystal oscillator and then grounding the shell of the crystal oscillator separately.
- If you think the island (dead zone) problem is very large, it doesn’t take much to define a ground via and add it in.
- When starting to lay out the wires, treat the ground wires equally. When laying out the wires, you should lay out the ground wires well. You cannot rely on adding vias after copper cladding to eliminate the unconnected ground pins. This will not work very well.
- It is best not to have sharp corners on the board (less than or equal to 180 degrees), because from an electromagnetic point of view, this constitutes a transmitting antenna! For others, there will always be an impact, but it is just a matter of whether it is large or small. I suggest using the edge line of the arc.
- Do not cover the empty area of the wiring in the middle layer of the multilayer board with copper. Because it is difficult for you to make this copper cladding “well grounded”.
- The metal inside the equipment, such as metal heat sinks, metal reinforcement strips, etc., must be “well grounded”.
- The heat dissipation metal block of the three-terminal regulator must be well grounded. The ground isolation belt near the crystal oscillator must be well grounded. If the grounding problem of copper cladding on the PCB is handled well, it will definitely be “more beneficial than harmful”. It can reduce the return area of the signal line and reduce the electromagnetic interference of the signal to the outside. (Library)