Blogs

It has a dielectric constant (DK) of 2.2 and is designed for applications that require high-speed signal transmission, such as in telecommunications, aerospace, and defense industries. The material is known for its low-loss properties, high thermal stability, and excellent dimensional stability. Where is the 5880 rogers used ？ Rogers 5880 is used in a variety…

Rogers 5880 prepreg is commonly used in high-frequency applications such as microwave and RF circuits, antennas, and satellite communication systems. It is also used in the aerospace industry for radomes and other applications that require high strength and low dielectric constant. GET IN TOUCH! What is Rogers 5880 Prepreg related to Rogers 5880 Prepreg is…

The recommended Zo values for Rogers 5880 are 50 ohms and 100 ohms. For example, if you want to design a PCB with 50-ohm transmission lines using Rogers 5880, and you want the dielectric layer to be 0.02 inches (0.508 mm) thick, you can calculate the required height as follows: H = (Zo x Er)…

For Rogers 5880, the Er value is typically 2.2, and the Zo value depends on the width and spacing of the transmission lines on the PCB. The recommended Zo values for Rogers 5880 are 50 ohms and 100 ohms. For example, if you want to design a PCB with 50-ohm transmission lines using Rogers 5880,…

The dielectric constant of Rogers 5880 can be calculated using the following formula: εr = C / C0 Where εr is the relative dielectric constant, C is the capacitance of a capacitor made with Rogers 5880 as the dielectric material, and C0 is the capacitance of the same capacitor with air as the dielectric material….

When it comes to designing and fabricating printed circuit boards (PCBs), there are severaloptions available. One of the popular choices is metal core PCBs, which are also known asMCPCBs. These PCBs are ideal for high-power LED applications, power supplies, and otherelectronic devices that require efficient heat dissipation. In this article, we willdiscuss the basics of…

metal core pcb technologyMetal core printed circuit board (MCPCB) technology is a type ofcircuit board that has a metal core instead of the traditional fiberglass substrate. Thistype of board is becoming increasingly popular in the electronics industry due to itsunique properties that make it ideal for certain applications. The metal core in an MCPCB provides several benefits over traditional…

A rigid-flex PCB is a printed circuit board that combines both rigid and flexible board technologies in a single design.This type of PCB is made up of multiple layers of rigid circuit boards that are interconnected by flexible circuitry. The rigid sections of the board provide stability and support for components,while the flexible sections allow the board to bend…

Rigid Flex PCB Cost Rigid flex PCBs are approximately seven times more expensive than an equivalent rigid PCB, largely due to the raw materials required, and in general lower overall yields. Rigid flex PCB’s use materials that are common to hard board and flexible circuit PCB manufacturers -core laminate, prepreg, copper foil, flexible laminates, coverlayers…

Rogers 5880LZ is used in various industries where high-performance RF and microwave circuit boards are required. Some of the industries where Rogers 5880LZ is used include: 1. Telecommunications: Rogers 5880LZ is used to make circuit boards for wireless communication systems such as cellular networks, Wi-Fi routers, and satellite communication systems. 2. Aerospace and defense: Rogers…

Rogers 5880LZ can be used to make high-performance RF and microwave circuit boards for a variety of applications. Some of the common applications of Rogers 5880LZ include: 1. Antennas: Rogers 5880LZ is an ideal material for making high-performance antennas for wireless communication systems, satellite communication systems, and radar systems. 2. Microwave circuits: Rogers 5880LZ is…

The Rogers 5880 data sheet documents the electrical and mechanical properties of the Rogers 5880 laminate material, which is a high-frequency circuit board substrate used in the design of microwave and RF circuits. The data sheet includes information on the material’s dielectric constant, loss tangent, thermal coefficient of expansion, and other key properties that affect its performance…

– Dielectric constant (Dk): 2.20 +/- 0.02– Dissipation factor (Df): 0.0009 @ 10 GHz– Thickness: 0.020″ (0.508 mm)– Copper foil thickness: 1 oz/ft2 (0.035 mm)– Operating temperature range: -55°C to +125°C– RoHS compliant For more detailed information, you can refer to the Rogers 5880 datasheet available on the Rogers Corporation website or contact a Rogers…

It is a PTFE composite material that is designed to provide excellent electrical performance at high frequencies. The substrate has a low dielectric constant of 2.2, which makes it ideal for use in microwave and millimeter-wave applications. It also has a low loss tangent, which means that it can transmit signals with minimal signal loss….

It is a PTFE composite material that is designed to provide excellent electrical performance at high frequencies. The substrate has a low dielectric constant of 2.2, which makes it ideal for use in microwave and millimeter-wave applications. It also has a low loss tangent, which means that it can transmit signals with minimal signal loss….